Configuring

The following stored procedures set and show configuration parameters, such as for binary log file retention.

mysql.rds_set_configuration

Specifies the number of hours to retain binary logs or the number of seconds to delay replication.

Syntax

CALL mysql.rds_set_configuration(name,value);

Parameters

target delay

The configuration parameters are stored permanently and survive any DB instance reboot or failover.

binlog retention hours

The binlog retention hours parameter is used to specify the number of hours to retain binary log files. Amazon RDS normally purges a binary log as soon as possible, but the binary log might still be required for replication with a MySQL database external to RDS.

The default value of binlog retention hours is NULL . For RDS for MySQL, NULL means binary logs aren't retained (0 hours).

To specify the number of hours to retain binary logs on a DB instance , use the mysql.rds_set_configuration stored procedure and specify a period with enough time for replication to occur, as shown in the following example.

call mysql.rds_set_configuration('binlog retention hours', 24);

For MySQL DB instances, the maximum binlog retention hours value is 168 (7 days).

source delay

Use the source delay parameter in a read replica to specify the number of seconds to delay replication from the read replica to its source DB instance. Amazon RDS normally replicates changes as soon as possible, but you might want some environments to delay replication. For example, when replication is delayed, you can roll forward a delayed read replica to the time just before a disaster. If a table is dropped accidentally, you can use delayed replication to quickly recover it. The default value of target delay is 0 (don't delay replication).

When you use this parameter, it runs mysql.rds_set_source_delay and applies CHANGE primary TO MASTER_DELAY = input value. If successful, the procedure saves the source delay parameter to the mysql.rds_configuration table.

To specify the number of seconds for Amazon RDS to delay replication to a source DB instance, use the mysql.rds_set_configuration stored procedure and specify the number of seconds to delay replication. In the following example, the replication is delayed by at least one hour (3,600 seconds).

call mysql.rds_set_configuration('source delay', 3600);

The procedure then runs mysql.rds_set_source_delay(3600) .

The limit for the source delay parameter is one day (86400 seconds).

target delay

Use the target delay parameter to specify the number of seconds to delay replication between a DB instance and any future RDS-managed read replicas created from this instance. This parameter is ignored for non-RDS-managed read replicas. Amazon RDS normally replicates changes as soon as possible, but you might want some environments to delay replication. For example, when replication is delayed, you can roll forward a delayed read replica to the time just before a disaster. If a table is dropped accidentally, you can use delayed replication to recover it quickly. The default value of target delay is 0 (don't delay replication).

For disaster recovery, you can use this configuration parameter with the mysql.rds_start_replication_until stored procedure or the mysql.rds_start_replication_until_gtid stored procedure. To roll forward changes to a delayed read replica to the time just before a disaster, you can run the mysql.rds_set_configuration procedure with this parameter set. After the mysql.rds_start_replication_until or mysql.rds_start_replication_until_gtid procedure stops replication, you can promote the read replica to be the new primary DB instance by using the instructions in Promoting a read replica to be a standalone DB instance .

To use the mysql.rds_rds_start_replication_until_gtid procedure, GTID-based replication must be enabled. To skip a specific GTID-based transaction that is known to cause disaster, you can use the mysql.rds_skip_transaction_with_gtid stored procedure. For more information about working with GTID-based replication, see Using GTID-based replication for Amazon RDS for MySQL .

To specify the number of seconds for Amazon RDS to delay replication to a read replica, use the mysql.rds_set_configuration stored procedure and specify the number of seconds to delay replication. The following example specifies that replication is delayed by at least one hour (3,600 seconds).

call mysql.rds_set_configuration('target delay', 3600);

The limit for the target delay parameter is one day (86400 seconds).

To verify the number of hours that Amazon RDS retains binary logs, use the mysql.rds_show_configuration stored procedure.

Examples

The following example displays the retention period: