如果可能，请在安装新粘合剂和重新密封之前打开你的设备并测试你的维修情况。
使用预切胶粘剂或双面胶带固定新电池。为了正确定位，请将新粘合剂涂在旧粘合剂所在的位置，而不是直接涂在电池上。将新电池牢固地按入到位。
要重新组装你的设备，请按逆序按照这些说明进行操作。用异丙醇 (>90%) 清洁相关区域后，在必要时涂抹新的粘合剂。
为获得最佳性能，请“校准新安装的电池”：将其充电至 100% 并继续充电至少 2 小时。然后使用你的设备，直到它因电池电量不足而关闭。最后，不间断地将其充电至 100%。
将你的电子垃圾送到
R2 或 e-Stewards 认证的回收商
]。
维修没有按计划进行？尝试一些
基本故障排除
，或向我们的
论坛
寻求帮助.
如果可能，请在安装新粘合剂和重新密封之前打开你的设备并测试你的维修情况。
使用预切胶粘剂或双面胶带固定新电池。为了正确定位，请将新粘合剂涂在旧粘合剂所在的位置，而不是直接涂在电池上。将新电池牢固地按入到位。
要重新组装你的设备，请按逆序按照这些说明进行操作。用异丙醇 (>90%) 清洁相关区域后，在必要时涂抹新的粘合剂。
为获得最佳性能，请“校准新安装的电池”：将其充电至 100% 并继续充电至少 2 小时。然后使用你的设备，直到它因电池电量不足而关闭。最后，不间断地将其充电至 100%。
将你的电子垃圾送到
R2 或 e-Stewards 认证的回收商
]。
维修没有按计划进行？尝试一些
基本故障排除
，或向我们的
论坛
寻求帮助.
Hello Ripple Blink, I'd recommend first removing adhesive remains by rolling them up on the tip of a spudger or scraping it off with the flat end of a spudger. Afterwards, you can use a lint-free cloth (or coffee filter) with a bit of isopropyl alcohol to clean the adhesion surfaces. See the first two steps of "
How to Use a Pre-Cut Adhesive Sheet
" for more information. Hope this helps!
Manuel Haeussermann
My dad replaced the battery in his A70, however he didn't wait for the alcohol to dry out and instead started using the phone. This led to major issues with touch disease and a glitchy screen. Once he had the sense to wait for the phone to dry it started working, however the fingerprint sensor has stopped working. Anyone know why? Could the sensor be damaged?
Ibrahim Anser
Hello Ibrahim Anser, normally the fingerprint sensor shouldn't be impacted by the steps detailed in this guide. Have you tried deleting the fingerprint data, restarting the phone and reregistering the fingerprint or does the fingerprint sensor not accept any inputs? You could also try using the Samsung Member app for hardware diagnostics of the fingerprint sensor. If those approaches fail, you could try checking if the fingerprint sensor cable is seated correctly on the daughterboard or if there is an issue with the connector (moisture or bent pins). As a last resort, you could remove the fingerprint sensor itself to check for moisture or other issues. You would need a Phillips screwdriver for that. Hope this is helpful!
Manuel Haeussermann
